non-IGMP switches will flood all ports on the switch with the IPTV stream regardless of whether that port has an active listener. IGMP snooping is a way for switches to optimize IPTV traffic such that the IPTV streams only get forwarded to the ports in which there is an active listener. The reason is because it is an IGMP snooping switch and is still reasonably priced at $33 on Amazon. Though may I make a recommendation for the Netgear GS105E (the "E" is important). Thanks everyone for the support and suggestions. I could try and hook things back up late tonight whenever everyone in the house is not watching TV and in bed and report back. Thank you for the link to that MoCA adapter I will check it out. I was thinking I had to have a coax connector coming from the RG in the mix. I could try a patch cable as Economist suggested to make sure they are working ok before trying this again.īdginmo you may be on to something here as I did not connect the main coax cable that feeds my main cable network to the input of the MoCA adapter. and used them in this same house over the same coax network and they worked fine on my Tivo's so I don't think the Cable run is too long. I don't think there is anything wrong with the MoCA adapters as they were not used a lot. My goal is to get near Gig speeds in other locations of my home and to be able to hook up an access point downstairs or to use a mesh system that supports ethernet backhaul in order to get the best speeds. I live in a big house and only get to enjoy gig speeds in one room of the house ( where the RG is connected). Actually, that works really well and is rock solid.Thanks everyone for the input and suggestions.įirst and foremost I have already bought and used the AirTie device that AT&T sells and it works just fine with the Pace 5268 but the problem is that it is slow. However, just to review, everything will work coax and HPNA with the BGW210 as long you connect the TPA311 to the RG and then hang the STB/DVRs off of it via a splitter. I can't explain it either, but that's the result of my test. If you want to use ethernet as the source of the IPTV packets then you must not have a coax cable connected. The DVR just says "no signal", but if you disconnect the coax it will link up just fine. In fact, it's so bad that if you have the DVR's ethernet port connected directly to the RG and have a coax cable connected at the same time that won't even work. No amount of reboots of the DVR and STBs will jump start anything. It refuses to work no matter what I tweak. In other words, you cannot use the IPH8005 as an ethernet-to-coax bridge and hope to run your STBs from coax. The Pace IPH8005 DVR happily bridges coax-to-ethernet, but it will refuse to go the other way ethernet-to-coax. Well, I had some time to really play around with this and I have some bad news. I'll let it run like this for a few weeks and report back. I expect this setup to be as reliable as ethernet. I suspect if you do decide to go the HPNA route you'll want a high quality HPNA compatible splitter, RG6 cable, and compression fittings all around. I will say that I did the wiring of the house myself and I opted for the more expensive Belden RG6 cable and the compression fittings. It all works flawlessly with no pixelation or loss of speed on the internet speed test. I've had multiple streams going while simultaneously doing a speed test from my laptop piggy backed on the ethernet port of one of the Cisco STBs. I connected an ethernet cable from the BGW210 to the TPA311 and then hung the 3-way Holland GHPNA splitter off it and hooked up the STBs/DVR to the splitter. The Cisco/Pace STBs/DVR already have coax connectors and the HPNA bridge builtin. Trendnet TPA311 HPNA Bridge ($40 - » a.co/7kN4nU3) Holland GHPNA 3-way Splitter 5-1500 Mhz ($5 - » a.co/bdriYOp) Again, I'm just experimenting with HPNA right now. When I got UVerse installed the tech and I hooked everything up via CAT6 going through a Linksys LGS308 switch. My home is wired with 2xCAT6 and 2xRG6 to each room. Why? Because I wanted to see for myself how it works out. So I recently (today) switched my setup from ethernet to coax via HPNA.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |